- #Gray transmission jack rebuild how to#
- #Gray transmission jack rebuild install#
- #Gray transmission jack rebuild manual#
- #Gray transmission jack rebuild download#
When disconnecting hoses and cables, make a drawing showing how each one is routed. Note: When removing brackets, mark their locations or make a simple drawing showing their locations. Note: You should be placing nuts and bolts in their labeled containers as you remove them. Remove any of the top bell housing to engine bolts that are accessible – otherwise the bolts will be removed later from underneath. Use a wire or strong bungee cord to hold the starter’s weight – do not hang from the starter wiring.ģ-C) Look closely at the top rear of the engine (back by the firewall) where the transmission bell housing bolts to the engine. Once the bolts are removed, just pull the starter out of the bell housing and push aside. Complete removal of the starter is normally not necessary. Any starter bolts that are not removed now will be removed later from underneath. Remove any starter bolts that are accessible. Still working under the hood, locate and disconnect any transmission electrical connectors you see.ģ-A) Remove any brackets, cables or hoses that connect the transmission to the engine.ģ-B) Now, locate the starter motor. If not, you can remove it later from underneath. If you can see this nut/bolt and it is easily accessible, go ahead and remove it along with dipstick tube now. The dipstick tube (also called transmission fill tube) is normally secured to the transmission or engine with a single nut or bolt. Have your vehicle identification number (VIN) readily available before making the call.Ģ-A) On some vehicles, it may be necessary to remove the black plastic air intake components to give your sufficient space to work.Ģ-B) Now, locate the transmission fluid dipstick – pull it out and set it aside.
#Gray transmission jack rebuild manual#
Check your Vehicle Owner’s Manual for the code or contact the service department of any auto dealership that sells your make vehicle for assistance. Note About Radio Code: On many newer vehicles, whenever the battery is disconnected a radio code is needed to get the stereo working again.
Safety Tip: To eliminate any chance of battery arching, after removing the battery cable, wrap a rag around the cable end and place a wrap over the battery terminal. Move the cable end away from the battery post. Park your vehicle on a flat concrete surface, put the shifter in Park, set the emergency brake, pull the hood latch and then open the hood.ġ) Remove the negative battery cable. Note: Depending on your vehicle, additional labeled containers may be needed. > Torque Converter to Flywheel Bolts (or Nuts) > Exhaust and Exhaust Heat Shield Bolts/Nuts > Transmission Oil Cooler Line Fitting Washers > Transmission Oil Fill/Dipstick Tube Bracket Bolt or Nut It’s best to get all the containers or baggies labeled before starting the job.įor removing the transmission from a rear wheel drive vehicle, you will need the following labeled containers/baggies. Organize nuts and bolts: For organizing nuts and bolts, we recommend using labeled plastic containers or baggies, whichever you have available. organized is important for two reasons… 1) it will save you time and frustration when re-installing the transmission and 2) it will insure all nuts and bolts are replaced in their original locations. Any injury, damage, or loss that may result from improper use of these tools, equipment, or from the information contained in this video is the sole responsibility of the user and not ChrisFix.Keeping nuts, bolts, washers, clamps, etc. Due to factors beyond the control of ChrisFix, no information contained in this video shall create any expressed or implied warranty or guarantee of any particular result. ChrisFix recommends safe practices when working on vehicles and or with tools seen or implied in this video.
ChrisFix assumes no liability for property damage or injury incurred as a result of any of the information contained in this video.
New videos every Week**ĭue to factors beyond the control of ChrisFix, I cannot guarantee against improper use or unauthorized modifications of this information. **If the video was helpful, remember to give it a "thumbs up" and consider subscribing.
#Gray transmission jack rebuild download#
Transmission Removal Checklist Download (FREE):
#Gray transmission jack rebuild how to#
Each detailed step will allow you to learn how to remove a transmission yourself so you can replace a clutch, flywheel, rear main seal, throw out bearing, pilot bearing, or just swap transmissions. I am doing this on a rear wheel drive 98 Mustang but the process is very similar on other rear wheel drive, front wheel drive, and even automatic cars and trucks. In this video I show you the 10 simple steps on how to replace a transmission.
#Gray transmission jack rebuild install#
Learn how to remove a transmission so you can replace your clutch or flywheel, or so you can rebuild your transmission and install a new one in your car or truck. Transmission removal, replacement, and installation.
0 kommentar(er)
